- Make
- SANDVIK TAMROCK
- Model
- 700 (Ranger Rock Pilot Surface Drills)
- Engine
- DT
- Year
- 2005-
Engine (DT)
Recommendation:
Transfer Gearbox (Stiebel)
Recommendation:
Notes
- a. Alternative recommendations, Gear oils, 2005, ISO12925-1 Type CKD, 77°F to 176°F: EP PAO 220
- b. Alternative recommendations, Gear oils, 2005, ISO12925-1 Type CKD, 95°F to 140°F: EP PAO 100
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.
Final Drive
Notes
- c. Alternative recommendations: ARCHER GOLD SYNTHETIC GEAR OIL SAE 75W-90
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.
Coolant
Recommendation:
Notes
- d. Do not mix coolants
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.
Hydraulics
Notes
- e. Viscosity selection criteria: Optimum viscosity, 60 cSt at operating temperature. Viscosity to remain between 50-110 cSt. at operating temperature; max cold temp peak, 110-200 cSt; min hot temperature peak, 30-50 cSt. Monograde oils are preferred but multigrades can be used if viscosity criteria cannot be met in prevailing operating conditions. ISO viscosity grade according to oil operating temperature; 12°C to 26°C, 32; 21°C to 32°C, 46; 29°C to 42°C, 68; 40°C to 51°C, 100; 48°C to 59°C, 150. Synthetic oils for temperatures below -20°C. Biodegradable & environmentally compatible oils recommended to ISO 15380.
- f. 2005, Tamrock factory fill oil, Shell Naturelle HFE 46 or HFE 68 synthetic ester. HFD-U synthetic, organic ester fluids for hazardous conditions also approved. Factory fill Tampere Plant, Fuchs Plantoflux 68-AT-S. Factory fill Lyon Plant, Condat D68. Also approved, Quaker Quintolubric 888-68. Guarantees not valid if these oils are not used. 20°C to 41°C, HM 46, 30°C to 50°C, HM 68
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.
Grease Points
Recommendation:
1st choice
ARCHER GOLD LUBRI-PLEX 2
Central Grease System (Safematic)
Notes
- g. Alternative recommendations, <32°F: GrLiE 00
- h. Alternative recommendations, >32°F: ARCHER GOLD LUBRI-TAC 2
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.
Chain Feed Gears
Notes
- i. Alternative recommendations: ARCHER GOLD SYNTHETIC GEAR OIL SAE 75W-90
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.
Chain Feed Planetary Gear
Recommendation:
Notes
- j. Alternative recommendations, Gear oils, 2005, ISO12925-1 Type CKD, 77°F to 176°F: EP PAO 220
- k. Alternative recommendations, Gear oils, 2005, ISO12925-1 Type CKD, 95°F to 140°F: EP PAO 100
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.
Compressor (Gardner Denver/Tamrotor)
Recommendation:
Notes
- l. 2005, Gardner Denver/Tamrotor compressor. Mineral based engine oil or synthetic compressor oil can be used.Minimum engine oil viscosity, 7.0 cSt. If operating temperature is continuously >90°C, mineral based oil change is 300 hours or 600 hours with synthetic compressor oil
- m. Alternative recommendations, 2005, -22°F to 104°F: RCOS 32
- n. Alternative recommendations, 2005, -4°F to 140°F: RCOS 46
- o. Alternative recommendations, Compressor, 2005, -4°F to 95°F: CF 5W-20
- p. Alternative recommendations, Compressor, 2005, 14°F to 86°F: CF 10W
- q. Alternative recommendations, Compressor, 2005, 23°F to 104°F: CF 10W-30
- r. Alternative recommendations, Compressor, 2005, 32°F to 104°F: CF 20W-20
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.
Compressor (underground rig) (Hydrovane)
Recommendation:
Notes
- s. Preferred grade: 0°C-40°C ; -10°C-40°C
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.
Drill Rod Thread
Recommendation:
Notes
- t. Sandvik 795-1960
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.
Rock Drill Shank
Recommendation:
Notes
- u. Alternative recommendations, Shank Lubrication, 2005, -15°F to 32°F: RD 32
- v. Alternative recommendations, Shank Lubrication, 2005, 14°F to 59°F: RD 68
- w. Alternative recommendations, Shank Lubrication, 2005, 41°F to 104°F: RD 100
- x. Alternative recommendations, Shank Lubrication, 2005, 68°F to 122°F: RD 150
- y. Alternative recommendations, Shank Lubrication, 2005, 86°F to 140°F: RD 220
- z. Alternative recommendations, Shank Lubrication, 2005, 104°F to 158°F: RD 320
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.
Track Rollers & Idlers
Recommendation:
Winch
Notes
- ba. Alternative recommendations: ARCHER GOLD SYNTHETIC GEAR OIL SAE 75W-90
- NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.